Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
siemens simodrive 611 universal hrs2 6sn1118 1nj01 0aa2 one axis resolver control board-0

For SIEMENS

Home >  Products >  For SIEMENS

Siemens SIMODRIVE 611 Universal HRS2 6SN1118-1NJ01-0AA2 One-Axis Resolver Control Board

Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: Germany
Warranty: 12 Months

  • Overview
  • Hot Selling Models
  • Recommended Products
Overview

Siemens · SIMODRIVE 611 universal HRS2

6SN1118-1NJ01-0AA2 One-Axis Resolver Positioning Control Board

Siemens 6SN1118-1NJ01-0AA2 is the SIMODRIVE 611 universal HRS2 one-axis control board for resolver feedback and positioning firmware. It supports high-resolution resolver evaluation, parameterizable analog monitoring outputs, serial commissioning and optional terminal or PROFIBUS-DP expansion.

At a Glance

Brand Siemens
Model 6SN1118-1NJ01-0AA2
Product Type HRS2 Resolver Drive Control Board
Core Function Closes speed, torque and positioning loops for one drive axis
Application or Compatible Series SIMODRIVE 611 universal power-module systems

HRS2 Identification

Confirm the final hardware digit 2 because the HRS2 board is tied to the later software baseline rather than the HRS or HR execution.

Resolver Match

Record the motor resolver pole-pair count and feedback wiring before transferring the drive parameter set.

Option-Module Check

Identify whether the installed board uses the TERMINALS option or one of the permitted PROFIBUS-DP option modules.

Product Overview

Siemens 6SN1118-1NJ01-0AA2 is the SIMODRIVE 611 universal HRS2 one-axis control board for resolver feedback and positioning firmware. It supports high-resolution resolver evaluation, parameterizable analog monitoring outputs, serial commissioning and optional terminal or PROFIBUS-DP expansion.

Runs the speed, torque and positioning functions for a resolver-equipped drive axis in the modular converter system. Evaluates one-to-six-pole-pair resolvers at selectable 12-bit or 14-bit resolution. Supports SimoCom U through the serial interface and accepts terminal or PROFIBUS-DP option hardware.

Ordering focus: Confirm the full 1NJ01-0AA2 HRS2 identity, one-axis power-module arrangement, resolver pole-pair data, software baseline, saved drive parameters and installed option module before ordering..

Key Functions

Closed-Loop Motion Control

Runs the speed, torque and positioning functions for a resolver-equipped drive axis in the modular converter system.

High-Resolution Feedback

Evaluates one-to-six-pole-pair resolvers at selectable 12-bit or 14-bit resolution.

Expandable Commissioning Interface

Supports SimoCom U through the serial interface and accepts terminal or PROFIBUS-DP option hardware.

Official Specifications

HRS2 Software Baseline Control-board software version 14.2 or later
Resolver Pole Pairs 1 to 6
Resolver Resolution 12-bit or 14-bit selectable evaluation
Resolver Limit Frequency at 12 Bit 957 Hz for HRS2
Resolver Limit Frequency at 14 Bit 479 Hz for HRS2
Maximum Speed at 12 Bit 57,420 r/min with a one-pole-pair resolver
Maximum Speed at 14 Bit Approximately 28,740 r/min with a one-pole-pair resolver
Analog Monitoring Outputs Two freely parameterizable outputs for the active drive at X441
Analog Output Range -10 V to +10 V
Analog Output Current 3 mA maximum
Analog Output Resolution 8 bits
Analog Output Update Updated in the speed-controller clock cycle
Analog Output Protection Short-circuit proof
X441 Connection 5-pin connector strip; 0.5 mm² maximum conductor cross-section
Serial Commissioning Port X471 can operate as RS232 or RS485
Terminal Option 6SN1114-0NA00-0AA0
PROFIBUS-DP Options 6SN1114-0NB00-0AA2 or 6SN1114-0NB01-0AA1
PROFIBUS-DP Board Requirement Control-board software version 3.1 or later

Frequently Asked Questions

Which feedback device is required by 6SN1118-1NJ01-0AA2?

Use a resolver with one to six pole pairs and configure its pole-pair count and resolution to match the motor.

How do I commission 6SN1118-1NJ01-0AA2 from a PC?

Connect SimoCom U through X471 in the selected RS232 or RS485 operating mode after disabling pulses as required for safe work.

Which software baseline belongs with 6SN1118-1NJ01-0AA2?

Use the HRS2 control-board baseline of version 14.2 or later and restore the proven drive parameter set.

Can 6SN1118-1NJ01-0AA2 use a PROFIBUS-DP option?

Yes, fit an approved option module and verify its hardware, connector, address and bus configuration before startup.

What should I record before replacing 6SN1118-1NJ01-0AA2?

Back up the drive parameters and record resolver data, option-module type, terminal assignments and firmware level.

How should I use the analog outputs on 6SN1118-1NJ01-0AA2?

Assign the required internal quantities in the parameter set and keep each output within the ±10 V and 3 mA limits.

Can 6SN1118-1NJ01-0AA2 replace a two-axis control board?

No, confirm the one-axis power-module arrangement and resolver execution rather than selecting a board only by the wider product family.

Compatibility & Ordering Notes

Before ordering 6SN1118-1NJ01-0AA2: Confirm the full 1NJ01-0AA2 HRS2 identity, one-axis power-module arrangement, resolver pole-pair data, software baseline, saved drive parameters and installed option module before ordering..

Compatibility Checklist

  • Confirm the installed converter belongs to the SIMODRIVE 611 universal platform.
  • Match the complete HRS2 -0AA2 suffix and software version 14.2 or later.
  • Verify the one-axis power module and resolver feedback execution.
  • Record the resolver pole-pair count, resolution and motor feedback wiring.
  • Restore the validated speed, torque and positioning parameter set.
  • Match any TERMINALS or PROFIBUS-DP option module and its connector assignment.
  • Check X441 monitoring-output loading and X471 commissioning-interface wiring.
Hot Selling Models
8MR2110-3B
ADN2010APA
K50LGRY2PQ
SAC-12P-1.5-PVC/FS
6XV1850-2LH20
3RX9 502-0BA00
AC-40 A-XHIC22
7000-40021-2341000
5SL6102-7 5ST3010
A-XHI04 XTCEXFAC04
CTB 41.35 1503280
13H 95559776
ZK1020-0101-0025
C4B4 084513
PS416-INP-400

Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
email goToTop

Evolo Automation is not an authorized distributor unless otherwise specified, representative, or affiliate of the manufacturer of this product. All trademarks and documents are the property of their respective owners and are provided for identification and informational.