Siemens SIMATIC ET 200iSP 6ES7132-7GD00-0AB0 4 DO 23.1 V DC/20 mA L-Shutdown Module
Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: Germany
Warranty: 12 Months
Email: [email protected]
whatsApp: +86-18150117685
- Overview
- Hot Selling Models
- Recommended Products
Overview
- Confirm that the exact article suffix and L-shutdown execution match the installed project.
- Match the ET 200iSP station, interface module and selected terminal module.
- Keep actuator and cable entity parameters within the Uo, Io, Po, Co and Lo limits.
- Match the L-shutdown circuit logic and wiring to the plant safety design.
- Reserve the two-byte address allocation and configure the required diagnostic parameters.
- Verify the zone, gas or dust group, certificates and enclosure against the site approval basis.
- Keep field wiring within the 500 m limit and account for the diagnostic thresholds.
Siemens · SIMATIC ET 200iSP
6ES7132-7GD00-0AB0 4 DO 23.1 V DC/20 mA L-Shutdown Electronic Module
Siemens 6ES7132-7GD00-0AB0 is a SIMATIC ET 200iSP electronic module for intrinsically safe digital-output applications. It provides the 23.1 V DC/20 mA L-shutdown execution for hazardous-area actuator circuits and combines field diagnostics with certified Ex entity limits.
At a Glance
| Brand | Siemens |
|---|---|
| Model | 6ES7132-7GD00-0AB0 |
| Product Type | Intrinsically Safe Digital Output Electronic Module |
| Core Function | Controls four Ex(i) actuator circuits with L-shutdown |
| Application or Compatible Series | SIMATIC ET 200iSP distributed I/O |
Exact Output Variant
Match the 23.1 V DC/20 mA L-shutdown execution because adjacent RD and GD variants use different shutdown logic or electrical ratings.
Intrinsic-Safety Calculation
Validate the actuator and cable circuit against the stated Uo, Io, Po, Co and Lo entity limits before installation.
Station Integration
Use the correct ET 200iSP terminal arrangement, station address allocation and diagnostic parameterization.
Product Overview
Siemens 6ES7132-7GD00-0AB0 is a SIMATIC ET 200iSP electronic module for intrinsically safe digital-output applications. It provides the 23.1 V DC/20 mA L-shutdown execution for hazardous-area actuator circuits and combines field diagnostics with certified Ex entity limits.
Drives Ex(i) field circuits through transistor outputs with a separate intrinsically safe L-shutdown input. Detects wire break and short circuit and reports diagnostic alarms, red group-error status and green output status. Separates the output circuits from the backplane bus and load voltage while retaining the certified Ex interface limits.
Key Functions
Intrinsically Safe Actuator Switching
Drives Ex(i) field circuits through transistor outputs with a separate intrinsically safe L-shutdown input.
Channel and Group Diagnostics
Detects wire break and short circuit and reports diagnostic alarms, red group-error status and green output status.
Hazardous-Area Electrical Separation
Separates the output circuits from the backplane bus and load voltage while retaining the certified Ex interface limits.
Official Specifications
| Hardware and Firmware Release | HW functional status 7; firmware V3.0.0 |
|---|---|
| Typical Current Consumption | 290 mA |
| Maximum Power-Bus Current | 340 mA with actuator supply |
| Typical Power Loss | 2.5 W |
| Maximum Address Space | 2 bytes per module |
| Output Switching Element | Transistor |
| No-Load Voltage Uao | 23.1 V DC |
| Internal Resistance Ri | 275 Ω |
| Operating Point E | 17.6 V DC at 20 mA |
| Output Delay | 2 ms maximum from 0 to 1; 1.5 ms maximum from 1 to 0 |
| Maximum Switching Frequency | 100 Hz with resistive load; 2 Hz with inductive load |
| Field Cable Length | 500 m maximum, shielded or unshielded |
| Wire-Break Diagnostic Threshold | R > 10 kΩ and I < 100 µA |
| Short-Circuit Diagnostic Threshold | R < 80 Ω for one output; R < 40 Ω for paralleled outputs |
| Ex Output Entity Limits for IIC | Uo 25.6 V; Io 96 mA; Po 0.61 W |
| Permissible External Entity Values for IIC | Co 98 nF; Lo 3 mH |
| Output-Circuit Isolation | No isolation channel-to-channel; isolated from the backplane bus and load voltage L+ |
| Degree of Protection | IP30 |
| Dimensions | 30 × 129 × 136.5 mm (W × H × D) |
| Approximate Weight | 255 g |
Frequently Asked Questions
Can 6ES7132-7GD00-0AB0 switch intrinsically safe actuators directly?
The module provides four transistor outputs for 23.1 V DC/20 mA Ex(i) circuits plus a separate intrinsically safe L-shutdown input.
Which terminal arrangement should I use with 6ES7132-7GD00-0AB0?
Use the ET 200iSP terminal module selected for the station’s screw- or spring-terminal scheme and approved hazardous-area configuration.
How should I calculate cable energy limits for 6ES7132-7GD00-0AB0?
For gas group IIC, keep the connected circuit within Uo 25.6 V, Io 96 mA, Po 0.61 W, Co 98 nF and Lo 3 mH.
What faults can 6ES7132-7GD00-0AB0 diagnose during commissioning?
The module can report wire break and short circuit through a parameterizable diagnostic alarm, a red group-error LED and green output-status LEDs.
What switching rates can I use with 6ES7132-7GD00-0AB0?
Keep switching at or below 100 Hz for resistive loads and 2 Hz for inductive loads.
Can I parallel outputs on 6ES7132-7GD00-0AB0 to increase current?
Do not parallel outputs for uprating because Siemens excludes this arrangement for explosion-protection reasons.
What enclosure check is required for 6ES7132-7GD00-0AB0 in a dust area?
The IP30 module must be installed in the corresponding approved enclosure for ATEX Zone 21 dust applications.