Siemens SITOP PSU100D 6EP1332-1LD00 PSU100D 24 V DC/3.1 A
Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: Thailand
Warranty: 12 Months
Email: [email protected]
whatsApp: +86-18150117685
- Overview
- Product Overview
- Key Functions
- Official Specifications
- Frequently Asked Questions
- Compatibility & Ordering Notes
- Hot Selling Models
- Recommended Products
Overview
SIEMENS SITOP PSU100D · STABILIZED POWER SUPPLY
6EP1332-1LD00 PSU100D 24 V DC/3.1 A
Official Siemens identification and technical data for 6EP1332-1LD00, prepared for accurate replacement matching and quotation.
At a Glance
| Article Number | 6EP1332-1LD00 |
| Manufacturer | Siemens |
| Platform | SITOP PSU100D |
| Product Type | PSU100D 24 V DC/3.1 A |
| Official Configuration | Single-phase 100 to 240 V AC input and regulated 24 V DC, 3.1 A output |
Exact Identification
Match the complete Siemens article number 6EP1332-1LD00 and the installed hardware configuration.
Official Configuration
Single-phase 100 to 240 V AC input and regulated 24 V DC, 3.1 A output.
Connection Check
AC mains input and 24 V DC load-output terminals.
Product Overview
6EP1332-1LD00 is officially identified by Siemens as 24 V DC / 3.1 A Stabilized Power Supply in the SITOP PSU100D product range.
Siemens identifies this SITOP PSU100D stabilized power supply with a 100 to 240 V AC input and a regulated 24 V DC, 3.1 A output.
Ordering focus: verify the complete 6EP1332-1LD00 article number, installed hardware configuration, connections and Siemens system documentation before replacement.
Key Functions
Model-Specific Configuration
6EP1332-1LD00: Single-phase 100 to 240 V AC input and regulated 24 V DC, 3.1 A output.
System Connection
AC mains input and 24 V DC load-output terminals.
Replacement Control
Use the full 6EP1332-1LD00 article number and official Siemens documentation to verify the installed configuration before replacement.
Official Specifications
| Rated Input Voltage | 100–240 V AC |
| Permissible Input Range | 85–264 V AC |
| Rated Line Frequency | 50/60 Hz |
| Rated Input Current | 1.5–1.0 A |
| Inrush Current | Less than 60 A |
| Mains Buffering | More than 15 ms at 115/230 V AC |
| Rated Output Voltage | 24 V DC |
| Output Voltage Setting Range | 22–28 V DC |
| Output Voltage Tolerance | ±2% |
| Rated Output Current | 3.1 A |
| Temperature Derating | From +50 °C at 2.5% per K |
| Efficiency at Rated Values | Approximately 86% |
| Parallel Operation | Supported |
| Short-Circuit Protection | Electronic, automatic restart |
| Radio Interference Suppression | EN 55022 Class B |
| Degree of Protection | IP20 |
| Ambient Operating Range | -10 to +70 °C |
| Installation | Wall mounting; variable mounting orientation |
| Dimensions (W × H × D) | 97 × 128 × 38 mm |
| Approximate Weight | 0.37 kg |
Official source: Siemens SITOP power supply technical data for the PSU100D wall-mounting range.
Frequently Asked Questions
Can 6EP1332-1LD00 operate from both 115 V and 230 V AC supplies?
Yes. The rated input is 100–240 V AC, and the permissible operating range is 85–264 V AC.
How far can technicians adjust the output of 6EP1332-1LD00?
The DC output can be set from 22 V to 28 V while the nominal rating remains 24 V.
Can two 6EP1332-1LD00 power supplies be connected in parallel?
Yes. Parallel operation is supported.
How does 6EP1332-1LD00 recover after an output short circuit?
Electronic short-circuit protection switches the unit into a restart behavior after the fault is cleared.
What mounting method is specified for 6EP1332-1LD00?
It is designed for wall mounting and permits variable mounting orientation.
What derating applies to 6EP1332-1LD00 at elevated temperature?
Above +50 °C, reduce the available output current by 2.5% per kelvin; the specified ambient range is -10 to +70 °C.
How much mains interruption can 6EP1332-1LD00 bridge?
The specified buffering time is more than 15 ms at 115 V or 230 V AC.
Compatibility & Ordering Notes
Compatibility Checklist for 6EP1332-1LD00
- Match the complete 6EP1332-1LD00 article number without shortening the suffix.
- Confirm compatibility with the installed SITOP PSU100D product range.
- Verify Single-phase 100 to 240 V AC input and regulated 24 V DC, 3.1 A output.
- Confirm AC mains input and 24 V DC load-output terminals.