Siemens SIMATIC S7-200 6ES7901-3CB30-0XA0 PC/PPI Multi-Master Cable
Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: China
Warranty: 12 Months
Email: [email protected]
whatsApp: +86-18150117685
- Overview
- Product Overview
- Key Functions
- Official Specifications
- Frequently Asked Questions
- Compatibility & Ordering Notes
- Hot Selling Models
- Recommended Products
Overview
6ES7901-3CB30-0XA0 RS-232/PPI Multi-Master Cable
Official Siemens S7-200 communication-cable data for programming, PPI networking and isolated RS-232-to-RS-485 conversion.
At a Glance
| Brand | Siemens |
|---|---|
| Model | 6ES7901-3CB30-0XA0 |
| Product Type | S7-200 RS-232/PPI Multi-Master cable |
| Core Function | Electrically isolated conversion between RS-232 and RS-485/PPI |
| Application / Compatible Series | STEP 7-Micro/WIN communication with SIMATIC S7-200 |
Exact Identification
Match the full Siemens order number and installed hardware version.
Engineering Fit
Confirm electrical data, terminals and the target SIMATIC system.
Configuration Check
Verify wiring and configuration against the official Siemens manual.
Product Overview
6ES7901-3CB30-0XA0 is officially identified by Siemens as PC/PPI Multi-Master Cable in the SIMATIC S7-200 product range.
Siemens identifies this PC/PPI multi-master cable for connecting an S7-200 controller to a serial PC interface. The official data sheet lists PPI and Freeport support, compatibility with GSM modems and a maximum transmission rate of 187.5 kbit/s.
Ordering focus: verify the complete 6ES7901-3CB30-0XA0 article number, installed hardware configuration, connections and Siemens system documentation before replacement.
Key Functions
Model-Specific Configuration
6ES7901-3CB30-0XA0: PC/PPI multi-master cable for S7-200 to serial PC connection, supporting PPI, Freeport and GSM modems.
System Connection
Serial PC interface and PPI/RS-485 connection; cable length 5.63 m.
Replacement Control
Use the full 6ES7901-3CB30-0XA0 article number and official Siemens documentation to verify the installed configuration before replacement.
Official Specifications
| Supply Voltage | 14.4 to 28.8 V DC |
|---|---|
| Supply Current at 24 V | 60 mA RMS max. |
| Galvanic Isolation | 500 V DC, RS-485 to RS-232 |
| PPI Baud-Rate Range | 9.6 to 187.5 kbaud |
| Freeport Baud-Rate Range | 1.2 to 115.2 kbaud |
| RS-485 Common-Mode Range | -7 V to +12 V for 1 s; 3 V RMS continuous |
| RS-485 Receiver Impedance | 5.4 kΩ min., including termination |
| RS-485 Bias Network | 10 kΩ to +5 V on B and 10 kΩ to GND on A |
| RS-485 Receiver Sensitivity | ±0.2 V; 60 mV typical hysteresis |
| RS-485 Differential Output | 2 V min. at 100 Ω; 1.5 V min. at 54 Ω |
| RS-232 Receiver Impedance | 3 kΩ min. |
| RS-232 Receiver Thresholds | 0.8 V min. low; 2.4 V max. high |
| RS-232 Transmitter Output | ±5 V min. at 3 kΩ |
| Operating Modes | PPI Multi-Master or PPI/Freeport |
| Port Mode Selection | Local/DCE or Remote/DTE |
| Character Format Selection | 10-bit or 11-bit in PPI/Freeport mode |
| Cable Sections | 0.8 m and 4.7 m |
| Status Indicators | Green Tx, Rx and PPI LEDs |
Frequently Asked Questions
Which controller family is 6ES7901-3CB30-0XA0 intended to connect?
It is designed for communication between a programming device and a SIMATIC S7-200 RS-485/PPI port.
Which PC interface is required for 6ES7901-3CB30-0XA0?
The programming-device side uses an RS-232 serial interface; this is not the USB/PPI cable variant.
Which PPI network rates are supported by 6ES7901-3CB30-0XA0?
PPI operation supports network rates from 9.6 kbaud through 187.5 kbaud.
How should 6ES7901-3CB30-0XA0 be set for direct PC programming?
Select Local/DCE operation and PPI mode; in PPI/Freeport operation also set the required baud rate and 11-bit format.
When can 6ES7901-3CB30-0XA0 be used in Freeport mode?
Freeport mode supports user-defined serial communication from 1.2 to 115.2 kbaud when the DIP switches and S7-200 program agree.
Does 6ES7901-3CB30-0XA0 isolate the computer from the PLC network?
Yes. The RS-232 and RS-485 sides are electrically isolated and tested at 500 V DC.
What should be verified before using 6ES7901-3CB30-0XA0 for an HMI transfer?
Confirm the panel supports the serial PC/PPI path, select a supported bit rate and use release 3 or later for higher-rate transfers.
Compatibility & Ordering Notes
Compatibility Checklist for 6ES7901-3CB30-0XA0
- Match the complete 6ES7901-3CB30-0XA0 article number without shortening the suffix.
- Confirm compatibility with the installed SIMATIC S7-200 product range.
- Verify PC/PPI multi-master cable for S7-200 to serial PC connection, supporting PPI, Freeport and GSM modems.
- Confirm Serial PC interface and PPI/RS-485 connection; cable length 5.63 m.