Siemens 6ES7151-3BA22-0AB0 SIMATIC ET 200S IM151-3 PN High Feature Interface
Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: Germany
Warranty: 12 Months
Email: [email protected]
whatsApp: +86-18150117685
- Overview
- Hot Selling Models
- Recommended Products
Overview
- Configure the station using STEP 7 V5.4 SP2 and allocate its I/O data within the 256-byte limit.
- Review electronic-module and motor-starter order numbers and product versions against the IM151-3 PN High Feature compatibility restrictions.
- Connect the 24 V DC supply and loop-through terminals according to the station potential arrangement.
- Assign the intended PROFINET device name before putting a replacement station into service.
6ES7151-3BA22-0AB0 SIMATIC ET 200S IM151-3 PN High Feature Interface
IM151-3 PN High Feature interface with an integrated two-port switch, up to 63 modules and Micro Memory Card device-name backup.
At a Glance
| Brand | Siemens |
|---|---|
| Model | 6ES7151-3BA22-0AB0 |
| Product Type | PROFINET interface module |
| Core Function | Transfer of distributed I/O and motor-starter data |
| Application | ET 200S stations on PROFINET IO |
Two-port PROFINET connection
An integrated switch connects the station through two RJ45 ports with automatic negotiation and crossover.
Station identification backup
A SIMATIC Micro Memory Card stores the device name and provides one route for firmware updates.
Interrupt and network diagnostics
Diagnostic, process, insert/remove and maintenance interrupts work alongside port diagnostics and SNMP/MIB-2 monitoring.
Product Overview
6ES7151-3BA22-0AB0 links an ET 200S station to PROFINET IO and supplies the station backplane bus while preparing data from the attached electronics and motor starters.
Its integrated Ethernet switch provides two RJ45 connections for network continuation, and the SIMATIC Micro Memory Card can preserve the device name for replacement and support firmware updates.
Key Functions
Two-port PROFINET connection
An integrated switch connects the station through two RJ45 ports with automatic negotiation and crossover.
Station identification backup
A SIMATIC Micro Memory Card stores the device name and provides one route for firmware updates.
Interrupt and network diagnostics
Diagnostic, process, insert/remove and maintenance interrupts work alongside port diagnostics and SNMP/MIB-2 monitoring.
Official Specifications
| Station module capacity | 63 modules maximum |
|---|---|
| Maximum backplane length | 2 m |
| I/O data address space | 256 bytes maximum |
| Ethernet connections | 2 RJ45 ports; 100BASE-TX |
| PROFINET transmission | 100 Mbit/s full duplex |
| Additional Ethernet rate | 10 Mbit/s for Ethernet services |
| Port adaptation | Autonegotiation and autocrossover |
| Realtime communication | IRTflex, RT Class 2 |
| Network diagnostics | SNMP with MIB-2, ping and ARP |
| Rated supply | 24 V DC with reverse-polarity protection |
| Power-failure bridging | 20 ms minimum |
| Supply current and loss | Approximately 200 mA; 2 W |
| Electrical isolation | Ethernet isolated from electronics |
| Permitted potential to rail | 75 V DC or 60 V AC |
| Insulation test | 500 V DC |
| Status indication | SF, BF, ON, and LINK plus RX/TX for each port |
| Width and mass | 60 mm; approximately 150 g |
Frequently Asked Questions
Can I continue an Ethernet line through 6ES7151-3BA22-0AB0?
The integrated two-port switch allows the network to continue through the two RJ45 connections.
How many station modules can 6ES7151-3BA22-0AB0 manage?
A station can contain up to 63 modules within a maximum backplane length of 2 m and a 256-byte I/O data address space.
Which STEP 7 release should I use to configure 6ES7151-3BA22-0AB0?
Configure the interface with STEP 7 V5.4 SP2.
Can 6ES7151-3BA22-0AB0 replace the earlier 6ES7151-3BA20-0AB0 interface?
The interface directly replaces that predecessor in an existing system without reconfiguration.
How do I preserve the device name when replacing 6ES7151-3BA22-0AB0?
Store the device name on the SIMATIC Micro Memory Card so that the replacement interface can use the saved identification.
Can I update firmware on 6ES7151-3BA22-0AB0 without a memory card?
Firmware can be updated through PROFINET IO as well as through a SIMATIC Micro Memory Card.
How can I monitor network problems on 6ES7151-3BA22-0AB0?
Use port diagnostics and the SF, BF, LINK and RX/TX indicators together with SNMP/MIB-2 network diagnostics.