Siemens 6ES7142-1BF30-0XA0 SIMATIC ET 200X EM 142 Digital Output Module
Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: Germany
Warranty: 12 Months
Email: [email protected]
whatsApp: +86-18150117685
- Overview
- Hot Selling Models
- Recommended Products
Overview
- Use this EM 142 as an ET 200X expansion module with the appropriate basic module.
- Match five-pole M12 cables and preserve the installed enclosure protection.
- Calculate total module current alongside individual output current and load-specific switching frequency.
- Keep output cables within the stated limit and do not parallel channels for current uprating.
6ES7142-1BF30-0XA0 SIMATIC ET 200X EM 142 Digital Output Module
EM 142 with eight 24 V DC / 1.2 A outputs, five-pole M12 connections and IP66/67 field protection.
At a Glance
| Brand | Siemens |
|---|---|
| Model | 6ES7142-1BF30-0XA0 |
| Product Type | Expansion digital output module |
| Core Function | Eight-channel field load switching |
| Application | ET 200X basic-module stations |
Field output expansion
Eight outputs add twenty-four-volt DC load-control points to an ET 200X basic module.
Electronic load protection
Electronic short-circuit protection limits output fault current.
Field-oriented indication
Green output-status indicators assist local signal checks at the machine.
Product Overview
6ES7142-1BF30-0XA0 expands an ET 200X station with eight electronic digital outputs for field-mounted load control.
The module uses five-pole M12 connections, electronic short-circuit protection and load-dependent switching limits, with a shared module-current budget.
Key Functions
Field output expansion
Eight outputs add twenty-four-volt DC load-control points to an ET 200X basic module.
Electronic load protection
Electronic short-circuit protection limits output fault current.
Field-oriented indication
Green output-status indicators assist local signal checks at the machine.
Official Specifications
| Digital outputs | 8; 24 V DC |
|---|---|
| Output rated current | 1.2 A per channel at 24 V DC |
| Permitted on-state current | 5 mA to 1.3 A |
| Maximum off-state residual current | 0.5 mA |
| Output connections | 5-pole M12 |
| Enclosure protection | IP66/67 |
| Maximum no-load supply current | 12 mA from 2L+; 35 mA from the 5 V backplane |
| Typical power loss | 1.5 W |
| Short-circuit protection | Electronic; typical response threshold 1.8 A |
| Minimum on-state voltage | 2L+ minus 1.2 V |
| Load resistance | 21 Ω to 4 kΩ |
| Maximum lamp load | 10 W per output |
| Switching-frequency limits | 100 Hz resistive; 0.5 Hz inductive DC13; 1 Hz lamp load |
| Total module current | 7 A up to 20°C; 5 A up to 50°C |
| Parallel output operation | No current uprating; redundant load control only within the same group |
| Maximum unshielded output cable | 30 m |
| Isolation | Backplane isolated from other circuits; no channel-to-channel isolation |
| Status and alarms | Green output-status LEDs; no alarms |
| Dimensions and approximate weight | 87 × 180 × 55 mm (W × H × D); module width 60 mm; 350 g |
Frequently Asked Questions
Can I obtain more load current by paralleling outputs of 6ES7142-1BF30-0XA0?
Parallel switching for current uprating is not permitted.
Can outputs of 6ES7142-1BF30-0XA0 be paralleled for redundant control of one load?
Redundant control is permitted only with outputs from the same group.
May all eight channels of 6ES7142-1BF30-0XA0 carry their full rated current simultaneously?
The combined load must remain within the module limit of seven amperes up to twenty degrees Celsius or five amperes up to fifty degrees Celsius.
What switching frequency can I use for an inductive DC13 load on 6ES7142-1BF30-0XA0?
The specified maximum switching frequency for an inductive DC13 load is one-half hertz.
How long can an unshielded output cable from 6ES7142-1BF30-0XA0 be?
The specified maximum unshielded output-cable length is thirty metres.
Does 6ES7142-1BF30-0XA0 generate diagnostic alarms for the controller?
The module has output-status indicators but does not provide alarms.
Are the output channels of 6ES7142-1BF30-0XA0 isolated from each other?
The outputs are not isolated channel to channel, although the backplane is isolated from the other circuits.