Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
siemens 6es7141 5af00 0ba0 simatic et 200al di 8x24vdc m12 module-0

For SIEMENS

Home >  Products >  For SIEMENS

Siemens 6ES7141-5AF00-0BA0 SIMATIC ET 200AL DI 8x24VDC M12 Module

Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: Germany
Warranty: 12 Months

  • Overview
  • Hot Selling Models
  • Recommended Products
Overview
SIMATIC ET 200AL

6ES7141-5AF00-0BA0 SIMATIC ET 200AL DI 8x24VDC M12 Module

Eight 24 V DC inputs through four M12 sockets, with a shared 0.7 A sensor supply and IP65/67 field protection.

At a Glance

Brand Siemens
Model 6ES7141-5AF00-0BA0
Product Type Digital input field block
Core Function Acquisition of distributed sensor states
Application ET 200AL machine I/O stations

Four M12 sensor sockets

Eight digital inputs are brought into the field block through four five-pole M12 connections.

Module-level supply protection

The sensor supply has electronic short-circuit protection and can generate a configured diagnostic alarm.

ET-Connection station link

Shielded four-pin M8 ET-Connection integrates the block into the distributed station.

Product Overview

6ES7141-5AF00-0BA0 collects eight digital input signals in an ET 200AL station through four five-pole M12 sensor connections.

The 30 mm wide field block uses Type 3 inputs, electronic sensor-supply protection and configurable diagnostics while connecting to the station through M8 ET-Connection cabling.

Ordering focus: Use the four M12 sensor connections and keep their combined sensor supply current within 0.7 A.
Key Functions

Four M12 sensor sockets

Eight digital inputs are brought into the field block through four five-pole M12 connections.

Module-level supply protection

The sensor supply has electronic short-circuit protection and can generate a configured diagnostic alarm.

ET-Connection station link

Shielded four-pin M8 ET-Connection integrates the block into the distributed station.

Official Specifications
Digital input bank 8 P-reading inputs; IEC 61131 Type 3
Sensor connector arrangement 4 five-pole M12 sockets
Nominal load supply 24 V DC; operating range 20.4–28.8 V
No-load current 25 mA rated
Supply through-current limits 4 A maximum on 1L+ and 4 A maximum on 2L+
Sensor supply outputs 4 outputs with 0.7 A combined maximum current
Typical power loss 1.9 W
Input switching levels Signal 0: −30 to +5 V; signal 1: +11 to +30 V
Typical high-state input current 3.2 mA
Input delay 1.2–4.8 ms on rising and falling transitions
Maximum unshielded sensor cable 30 m
Two-wire sensor quiescent current 1.5 mA maximum
Fault indication Green channel LEDs and green/red module diagnostic LED
Electrical isolation Inputs isolated from backplane; no isolation between channels
Isolation type test 707 V DC
Enclosure protection IP65/67
Operating ambient −30 to +55°C
Maximum operating altitude 5000 m with additional restrictions above 2000 m
Supply and ET-Connection 4-pole M8 supply; shielded 4-pin M8 ET-Connection
Dimensions and mass 30 × 159 × 40 mm (W × H × D); approximately 145 g
Frequently Asked Questions

How many M12 sockets are used for the eight inputs of 6ES7141-5AF00-0BA0?

The block has four five-pole M12 sensor connections serving eight digital inputs.

What total current is available to sensors powered by 6ES7141-5AF00-0BA0?

The four sensor supply outputs share a maximum combined current of 0.7 A.

Which device description is needed to configure 6ES7141-5AF00-0BA0?

Use GSD revision 5 or later for PROFIBUS integration or GSDML V2.3.1 for the stated PROFINET integration.

Can I configure 6ES7141-5AF00-0BA0 with classic STEP 7?

Classic STEP 7 support starts at V5.5 SP4 Hotfix 7.

Can all inputs on 6ES7141-5AF00-0BA0 remain active at the maximum ambient temperature?

All eight inputs may be active up to +55°C.

Does 6ES7141-5AF00-0BA0 provide galvanic isolation between adjacent input channels?

The channels are not isolated from each other but are isolated from the backplane bus.

How far from 6ES7141-5AF00-0BA0 can an unshielded sensor connection run?

Keep an unshielded sensor cable within 30 m.

Compatibility & Ordering Notes
Before ordering 6ES7141-5AF00-0BA0: Use the four M12 sensor connections and keep their combined sensor supply current within 0.7 A.

Before installation

  • Use five-pole M12 sensor connectors and the specified four-pole M8 supply connection.
  • Allocate sensor loads within the shared 0.7 A limit.
  • Select a supported STEP 7 or TIA Portal release and the matching station device description.
  • Preserve field-connection sealing and keep the input cable length within its limit.
Hot Selling Models
4021506
T0-3-8342/I1/SVB
301SN-6
3TH4346-0A
7700-40041-1610500
DSNU25100PPVS2
Z2S6A3-64 / R900347500
M65 XTCE065D
1020000000
MS6-EM1-1/2-R-SA
VAL-MS 230 ST 2798844 + VAL-MS BE/FM 2817738
RAC1DF 25W17
ABB 2CDS251001R0104
efector100 IA0002 IA-2010-BB0W
ZM-32-PKZ2 + NHI-11-PKZ

Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
email goToTop

Evolo Automation is not an authorized distributor unless otherwise specified, representative, or affiliate of the manufacturer of this product. All trademarks and documents are the property of their respective owners and are provided for identification and informational.