Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
siemens 6es7132 6bf00 0ba0 simatic et 200sp dq 8x24vdc 0 5a st module-0

For SIEMENS

Home >  Products >  For SIEMENS

Siemens 6ES7132-6BF00-0BA0 SIMATIC ET 200SP DQ 8x24VDC/0.5A ST Module

Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: Germany
Warranty: 12 Months

  • Overview
  • Hot Selling Models
  • Recommended Products
Overview
SIEMENS SIMATIC ET 200SP

6ES7132-6BF00-0BA0 SIMATIC ET 200SP DQ 8x24VDC/0.5A ST Module

An eight-channel sourcing output module with 0.5 A per output, a 4 A module limit, configurable diagnostics and output quality information.

At a Glance

Brand Siemens
Model 6ES7132-6BF00-0BA0
Product Type Standard digital output electronics module
Core Function Driving binary field loads from the distributed I/O station
Application ET 200SP stations with a compatible interface and A0 BaseUnit

Eight sourcing outputs

The 24 V DC output bank supplies up to 0.5 A per channel and 4 A in total.

Channel diagnostics

Configurable diagnostics cover wire break and short circuits, with local status and DIAG indication.

A0 BaseUnit interface

The 15 mm-wide electronics module uses an A0 BaseUnit and CC02 identification.

Product Overview

6ES7132-6BF00-0BA0 adds eight sourcing digital outputs to an ET 200SP station, combining field-load switching with configurable diagnostic functions.

The output area occupies one byte, with a further byte when quality information is used; wire-break diagnostics can produce a small residual current in the off state.

Ordering focus: Match the A0 BaseUnit and interface configuration, check the hardware status for station-size limits, and coordinate output diagnostics with the connected loads.
Key Functions

Drive discrete DC loads

Eight sourcing outputs operate from a nominal 24 V DC supply, with a 0.5 A channel rating and a 4 A module total.

Track output and supply faults

The module supports diagnostics for supply voltage, wire break and short circuits, with channel-status LEDs and a green/red DIAG LED.

Set the output response in the project

Output substitute values and quality information support the configured controller response, while parameter record 128 permits parameter changes during RUN.

Official Specifications
Output Bank 8 sourcing digital outputs
Supply Voltage 24 V DC nominal; permissible range 19.2–28.8 V DC
Maximum No-Load Current Consumption 35 mA
Typical Power Dissipation 1 W
Output Address Space 1 byte, plus 1 byte for quality information
Rated Channel Current 0.5 A
Maximum Module Current 4 A
Typical Short-Circuit Response Threshold 0.7–1.3 A
Maximum Signal-0 Residual Current 0.1 mA
Load-Resistance Range 48 Ω–12 kΩ
Maximum Resistive-Load Output Delay 50 µs OFF-to-ON; 100 µs ON-to-OFF at rated load
Maximum Switching Frequency 100 Hz resistive; 2 Hz inductive; 10 Hz lamp load
Maximum Lamp Load 5 W per output
Maximum Field-Cable Length 1000 m shielded; 600 m unshielded
Isolation Test Voltage 707 V DC, type test
Permitted Potential Difference 75 V DC or 60 V AC between different circuits, basic insulation
Operating Ambient Temperature 0–60 °C horizontal; 0–50 °C vertical
Module Width 15 mm
Approximate Weight 28 g
Frequently Asked Questions

Why might an LED load flicker with an output on 6ES7132-6BF00-0BA0 switched off?

Wire-break diagnostics produce a small off-state residual current whose level depends on the diagnostic setting.

Can I parallel two outputs on 6ES7132-6BF00-0BA0 to increase load capacity?

Parallel connection for increased output performance is not permitted.

Which BaseUnit type should I select for 6ES7132-6BF00-0BA0?

The electronics module uses a type A0 BaseUnit with CC02 identification.

How much output address space should I reserve for 6ES7132-6BF00-0BA0 when using quality information?

Reserve one output byte and one additional byte for quality information.

Can I change parameters on 6ES7132-6BF00-0BA0 while the CPU is in RUN?

WRREC can transfer parameter data record 128 during RUN, while a restart restores the parameters held in the STEP 7 project.

What station-size restriction applies to early hardware versions of 6ES7132-6BF00-0BA0?

Modules up to functional status 002 do not support station configurations with more than 32 I/O modules.

Can all eight outputs on 6ES7132-6BF00-0BA0 carry their rated current together?

The module permits a total of 4 A up to 60 °C horizontally or 50 °C vertically.

Compatibility & Ordering Notes
Before ordering 6ES7132-6BF00-0BA0: Select the exact Standard output article, type A0 BaseUnit and appropriate interface configuration, accounting for the hardware-status station limit and diagnostic residual current.

Compatibility Checklist for 6ES7132-6BF00-0BA0

  • Use a type A0 BaseUnit and the CC02 identification arrangement.
  • For functional status up to 002, keep the station within 32 I/O modules.
  • For firmware V1.1.0, use TIA Portal V13 Update 3 or the specified STEP 7 V5.5 SP3 HSP0230 V4.0 support.
  • Keep channel loading within 0.5 A and module loading within 4 A.
  • Do not parallel outputs to increase current capacity.
  • Account for the off-state residual current when selecting LED loads and wire-break diagnostics.
Hot Selling Models
6GK1143-0AB01 6ES5376-1AA11
ABB AE9-30-00 CAL5-11
BMF0043 303K-PS-C-2A-SA2-S49-00.3
3RV1021-1BA15
ADN-32-20-IPA
FK-M16 2065
1527570000
ABB S 203C S2C-H6R
3RT1325-1BB40 3RH1921-1FA22 + 3RT1926-1ER00
E3F2-10DB4-P1
E3F2-10LB-P1
3RV2011-1JA20 3RV2901-2F
3RK2400-1DQOO-OAA3
6ES7194-4DC00-0AA0
163B611BAAA

Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
email goToTop

Evolo Automation is not an authorized distributor unless otherwise specified, representative, or affiliate of the manufacturer of this product. All trademarks and documents are the property of their respective owners and are provided for identification and informational.