Siemens SIMATIC DP 6ES7972-4AA50-0XA0 PRB Segment Controller
Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: Germany
Warranty: 12 Months
Email: [email protected]
whatsApp: +86-18150117685
- Overview
- Hot Selling Models
- Recommended Products
Overview
- Confirm the application uses a multi-segment Power Rail network.
- Calculate segment A-B length and sensor position for the actual vehicle speed and telegram length.
- Account for one fewer permitted vehicle in each segment for every connected segment controller.
- Use an IEC 61131 Type 2 two-wire initiator with the required electrical thresholds.
- Match the three B-coded Power Rail connectors and the A-coded supply and I/O connectors.
- Provide 20.4 to 28.8 V DC SELV and a low-resistance functional-earth connection.
- Record any non-default DIP-switch functions before replacement or recommissioning.
Siemens · SIMATIC DP Power Rail Booster
6ES7972-4AA50-0XA0 PRB Segment Controller
Siemens designed this PRB Segment Controller as a network component and Power Rail Booster accessory for automatic changeover between adjoining PRB segments. It switches the interim segment between the two neighboring supplies so mobile equipment can cross a segment boundary without an operational interruption to message traffic.
At a Glance
| Brand | Siemens |
|---|---|
| Model | 6ES7972-4AA50-0XA0 |
| Product Type | Power Rail Booster Segment Controller |
| Core Function | Maintains communication while moving equipment crosses a rail-segment boundary |
| Application or Compatible Series | Multi-segment Power Rail networks for conveyors, cranes, lifts and traversing systems |
Rail Geometry Check
Calculate the interim-segment and control-plate geometry for the vehicle speed, data length and network baud rate.
Sensor Arrangement
Use the specified external two-wire initiator and place it at the calculated position relative to the segment boundary.
Interface Wiring
Verify the three Power Rail connections, 24 V supply, digital input, optional PLC output and functional earth.
Product Overview
Siemens designed this PRB Segment Controller as a network component and Power Rail Booster accessory for automatic changeover between adjoining PRB segments. It switches the interim segment between the two neighboring supplies so mobile equipment can cross a segment boundary without an operational interruption to message traffic.
The controller switches the A-B interim segment between adjacent Power Rail segments as the vehicle crosses the boundary. The changeover sequence works for travel in either direction without requiring stationary-control changeover logic. Seven front LEDs identify segment traffic, system faults, supply state, sensor input and PLC output state.
Key Functions
Automatic Segment Changeover
The controller switches the A-B interim segment between adjacent Power Rail segments as the vehicle crosses the boundary.
Direction-Independent Operation
The changeover sequence works for travel in either direction without requiring stationary-control changeover logic.
Local Fault Indication
Seven front LEDs identify segment traffic, system faults, supply state, sensor input and PLC output state.
Official Specifications
| Operating Supply | 20.4 to 28.8 V DC, typically 24 V SELV, galvanically isolated |
|---|---|
| Rated Current Consumption | 150 mA maximum |
| Inrush Current | 15 A maximum for approximately 200 microseconds |
| Supply Protection | 6 A category C circuit-breaker |
| Maximum Power Dissipation | 4.5 W |
| Supported Transmission Speeds | 9.6, 19.2, 45.45, 93.75, 187.5 and 500 kbit/s |
| Transmission-Speed Selection | Automatic |
| Power Rail Signal Rating | Differential signal up to 60 V with 5 A maximum current |
| Power Rail Input Withstand | Up to 60 V differential continuously and 2.5 kV to ground |
| Digital Output Switching Rating | 24 V AC/DC and 0.2 A maximum |
| Digital Output Isolation | 4000 V AC |
| Digital Input Circuit | 24 V DC +/-10% with 1.4 kohm internal sensor-supply resistance |
| Sensor-Signal Debounce | Approximately 3 ms |
| Sensor Fault Monitoring | Open circuit below 0.5 mA and short circuit or overload above 15 mA, each evaluated after approximately 100 ms |
| Digital Input Thresholds | Active above 6.2 mA or below 17.3 V; inactive below 3.7 mA or above 18.7 V |
| Sensor Requirement | Two-wire sensor to IEC 61131 Type 2; Siemens reference 3RG4014-0JB00 |
| Circular Connector Rating | M12/PG9, 5 poles, 3 A at 60 V DC, 0.25 to 0.75 mm2 conductors and 6 to 8 mm round cable |
| Ambient Conditions | 0 to +60 deg C operation; -40 to +70 deg C storage; below 95% relative humidity without condensation |
| Enclosure and Mounting | IP54 with unrestricted mounting position |
| Weight | 760 g |
Frequently Asked Questions
Which moving systems are appropriate for 6ES7972-4AA50-0XA0?
Typical applications include powered overhead conveyors, storage and retrieval machines, cranes, lifts and traversing tracks.
Does 6ES7972-4AA50-0XA0 require a sensor at the segment boundary?
Normal operation requires an external two-wire initiator positioned from the calculated rail and control-plate geometry.
Can 6ES7972-4AA50-0XA0 operate for travel in both directions?
The changeover function is independent of vehicle travel direction.
How does 6ES7972-4AA50-0XA0 select the communication speed?
The controller detects the supported Power Rail transmission rate automatically.
What connections should I complete before energizing 6ES7972-4AA50-0XA0?
Connect the sensor and optional PLC output, all three Power Rail segments, the 24 V supply and the low-resistance functional earth.
How can I diagnose a fault on 6ES7972-4AA50-0XA0?
Seven front indicators show segment message traffic, system status, supply health, sensor input and PLC output.
Can 6ES7972-4AA50-0XA0 be added to an existing Power Rail installation?
Retrofit installation is possible when the segment geometry, vehicle count, sensor placement and other configuration limits are satisfied.