Siemens 6ES7151-3AA22-0AB0 SIMATIC ET 200S IM151-3 PN Interface Module
Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: Germany
Warranty: 12 Months
Email: [email protected]
whatsApp: +86-18150117685
- Overview
- Hot Selling Models
- Recommended Products
Overview
- Configure this interface with STEP 7 V5.4 SP2 and match the connected electronic-module revisions.
- Keep the station within sixty-three modules and a two-metre backplane.
- Select the required SIMATIC Micro Memory Card capacity and switch off supply power before handling it.
- Apply the predecessor-specific replacement conditions and clear a retained device name separately when preparing a used spare.
6ES7151-3AA22-0AB0 SIMATIC ET 200S IM151-3 PN Interface Module
IM151-3 PN with an integrated two-port switch, removable device-name storage and support for up to sixty-three station modules.
At a Glance
| Brand | Siemens |
|---|---|
| Model | 6ES7151-3AA22-0AB0 |
| Product Type | Distributed I/O interface module |
| Core Function | Station communication and backplane supply |
| Application | ET 200S electronic modules and motor starters |
Two-port station connection
An integrated two-port switch connects the station to PROFINET IO.
Removable device-name storage
A SIMATIC Micro Memory Card stores the configured device name for station handling.
Station and port diagnostics
Diagnostic, process, insertion/removal and maintenance alarms support station monitoring.
Product Overview
6ES7151-3AA22-0AB0 connects an ET 200S station to PROFINET IO and supplies its backplane bus.
The interface provides two RJ45 ports, port diagnostics and removable storage for the device name, with station expansion bounded by module count and bus length.
Key Functions
Two-port station connection
An integrated two-port switch connects the station to PROFINET IO.
Removable device-name storage
A SIMATIC Micro Memory Card stores the configured device name for station handling.
Station and port diagnostics
Diagnostic, process, insertion/removal and maintenance alarms support station monitoring.
Official Specifications
| PROFINET interfaces | 2 RJ45 ports; 100BASE-TX |
|---|---|
| Transmission rates | 10 Mbit/s for Ethernet services; 100 Mbit/s full duplex for PROFINET IO |
| Ethernet functions | Autonegotiation and autocrossing; ping, ARP and SNMP / MIB-2 |
| Realtime communication | IRTflex, RT Class 2 |
| Maximum station module count | 63 |
| Maximum backplane length | 2 m |
| Maximum I/O address space | 256 bytes of I/O data |
| Nominal electronic supply | 24 V DC |
| Approximate supply current | 200 mA |
| Approximate power dissipation | 2 W |
| Minimum supply interruption buffering | 20 ms |
| Potential separation | Ethernet isolated from electronics; backplane and supply not isolated from electronics |
| Permitted rail potential difference | 75 V DC or 60 V AC |
| Isolation test voltage | 500 V DC |
| Status indicators | Red SF and BF; green ON and LINK; yellow RX/TX per port |
| Interface identification | Vendor ID 002A hex; Device ID 0301 hex |
| Module width | 60 mm |
| Approximate weight | 150 g |
Frequently Asked Questions
Can the station behind 6ES7151-3AA22-0AB0 exceed two metres if it contains fewer than sixty-three modules?
The backplane remains limited to two metres even when the station uses fewer than the maximum sixty-three modules.
Can I combine small modules into one byte with 6ES7151-3AA22-0AB0?
The interface supports packing modules together into one byte of the I/O address space.
Will a factory reset of 6ES7151-3AA22-0AB0 automatically remove the device name from its memory card?
The device name stored on the SIMATIC Micro Memory Card is retained during that reset and must be cleared separately when required.
Can I insert or remove the memory card of 6ES7151-3AA22-0AB0 while supply power is on?
Card operation is guaranteed only when the card is inserted or removed with supply power switched off.
Is a 64 KB memory card sufficient for the firmware-update procedure of 6ES7151-3AA22-0AB0?
A 64 KB card can store the device name, while the firmware-update procedure requires a card of at least 2 MB.
Can I use a 6ES7138-4DF01-0AB0 serial module at product version four with 6ES7151-3AA22-0AB0?
That serial-module order number through product version four is excluded from the supported station modules.
What extra conditions apply when 6ES7151-3AA22-0AB0 replaces an IM151-3AA10?
The replacement requires fifteen millimetres of free space to the left, STEP 7 V5.3 SP3 and the specified adaptation of the user program for PROFINET IO.