Siemens 6ES7132-7RD22-0AB0 SIMATIC ET 200iSP 4 DO 17.4 V/40 mA Shutdown H Module

Overview

SIEMENS SIMATIC ET 200iSP

6ES7132-7RD22-0AB0 SIMATIC ET 200iSP 4 DO 17.4 V/40 mA Shutdown H Module

Operate four intrinsically safe field outputs with a high-active shutdown input that deactivates all channels independently of the output process image.

At a Glance

Brand	Siemens
Model	6ES7132-7RD22-0AB0
Product Type	Intrinsically safe digital output electronics
Core Function	Operate field actuators with group shutdown
Application	ET 200iSP distributed process I/O

Field actuator outputs

Four outputs serve suitable Ex i solenoid valves, DC relays and actuators.

High-active group shutdown

An intrinsically safe HIGH signal deactivates all four outputs together.

Paired output loading

Approved channel pairs can be connected in parallel on the same module for increased actuator current.

Product Overview

6ES7132-7RD22-0AB0 is a four-channel ET 200iSP output module with the SHUT DOWN H function. The 17.4 V/40 mA output characteristic supports compatible intrinsically safe field actuators, with an additional input for simultaneous actuator shutdown.

The shutdown function acts on all output channels without changing the output process image, and configurable diagnostics report channel faults; two approved outputs on the same module can be paralleled for a higher-current actuator.

Ordering focus: Match the actuator to the output characteristic and intrinsic-safety circuit limits, and keep H-shutdown wiring separate from L-shutdown module wiring.

Key Functions

Switch intrinsically safe actuator circuits

Four digital outputs control compatible Ex i solenoid valves, relays and actuators within the output characteristic and circuit limits.

Deactivate every output through one signal

The high-active intrinsically safe shutdown input disables channels 0 through 3 independently of the output process image.

Increase available actuator current with approved pairs

Channels 0 and 1 or channels 2 and 3 can be connected in parallel on the same module using the specified jumper and load terminals.

Official Specifications

Output Arrangement	4 transistor output channels plus 1 intrinsically safe high-active shutdown input
No-Load Output Voltage	17.4 V DC
Output Characteristic Break Point	10.7 V at 40 mA for one output; 80 mA with an approved parallel pair
Internal Output Resistance	167 Ω
Power-Bus Current Consumption	Typical 380 mA; maximum 400 mA
Module Power Dissipation	2.8 W
Maximum Field Cable Length	500 m, shielded or unshielded
Electrical Isolation	Outputs isolated from backplane, power bus and shutdown input; no isolation between output channels
Permitted Circuit Potential Difference	60 V DC or 30 V AC
Short-Circuit Detection Threshold	Load plus line resistance below 80 Ω for one output or below 40 Ω for a parallel pair
Wire-Break Detection	Load plus line resistance above 10 kΩ and current below 100 µA
Maximum Output Residual Current	25 µA
Maximum Switching Frequency	100 Hz with resistive loads; 2 Hz with inductive loads
Shutdown Input Intrinsic-Safety Limits	Ui 28 V; Pi 1.2 W; Ci 3 nF; Li 0 mH
Minimum Shutdown Switching Signal	10.5 V and 2 mA
Maximum Shutdown-Signal Current	8 mA per module when supplied through a safety barrier
Local Status Indicators	Green output LED per channel and red SF group-fault LED
Dimensions and Approximate Weight	30 × 129 × 136.5 mm (W × H × D); 255 g

Official source:Siemens product manual and technical specifications

Frequently Asked Questions

Can I shut down every channel of 6ES7132-7RD22-0AB0 through one field signal?

Yes, a high-active intrinsically safe switching signal at the shutdown input deactivates all four outputs.

Does 6ES7132-7RD22-0AB0 support High-active group shutdown for mobile equipment?

No, actuator shutdown does not affect the output process image.

Which channels can I parallel on 6ES7132-7RD22-0AB0 for a higher-current actuator?

Only channels 0 and 1 or channels 2 and 3 on the same module may be connected in parallel using the specified terminal arrangement.

Which terminal modules can carry 6ES7132-7RD22-0AB0?

The electronics can be mounted on TM-IM/EM 60S, TM-IM/EM 60C, TM-EM/EM 60S or TM-EM/EM 60C terminal modules.

Will 6ES7132-7RD22-0AB0 operate if no intrinsically safe shutdown signal is applied?

Yes, the H-shutdown module operates with its normal functionality when no shutdown signal is applied.

How should I wire the shutdown signal if I plan to hot-swap 6ES7132-7RD22-0AB0?

Connect each module directly to the shutdown-signal source because a daisy-chained signal path through the terminals is interrupted when a module is removed.

Is the no-load voltage of 6ES7132-7RD22-0AB0 also available at the rated 40 mA operating point?

No, the output characteristic has its 40 mA break point at 10.7 V rather than the 17.4 V no-load voltage.

Compatibility & Ordering Notes

Before ordering 6ES7132-7RD22-0AB0: Select the H-shutdown variant and compatible terminal module, then match the actuator, cable and intrinsically safe shutdown source to the circuit parameters.

Compatibility Checklist for 6ES7132-7RD22-0AB0

• Keep the shutdown-signal circuits for H and L variants separate.
• Use only the specified same-module channel pairs for parallel output operation.
• Connect each module directly to the shutdown source when hot swapping with actuator shutdown enabled.
• When replacing an earlier 7RD21 version, change the terminal coding element to the correct successor coding.

Hot Selling Models