Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
siemens 6es7132 6hd01 0bb1 et 200sp rq 4x120vdc 230vac 5a st relay output module-0

For SIEMENS

Home >  Products >  For SIEMENS

Siemens 6ES7132-6HD01-0BB1 ET 200SP RQ 4x120VDC–230VAC/5A ST Relay Output Module

Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: Germany
Warranty: 12 Months

  • Overview
  • Hot Selling Models
  • Recommended Products
Overview
SIMATIC ET 200SP

6ES7132-6HD01-0BB1 ET 200SP RQ 4x120VDC–230VAC/5A ST Relay Output Module

A four-channel relay module with normally open contacts, substitute values and supply diagnostics.

At a Glance

Brand Siemens
Model 6ES7132-6HD01-0BB1
Product Type Relay output module
Core Function Switching isolated load circuits
Application Distributed actuator control

Switch independent load circuits

Four relay outputs provide a maximum of 5 A per channel, subject to load type and thermal limits.

Choose the wiring arrangement

Use a B1 BaseUnit for two-wire connection or a B0 BaseUnit for three-wire connection.

Control fault behavior

Substitute values and supply-voltage monitoring support defined operation during faults.

Product Overview

6ES7132-6HD01-0BB1 switches AC or DC loads through four isolated normally open relay contacts.

The module supports diagnostic alarms and configurable substitute values, with BaseUnit selection determining the supported field-wiring arrangement.

Ordering focus: Choose a B0 or B1 BaseUnit and size the external protection for each connected load.
Key Functions

Switch independent load circuits

Four relay outputs provide a maximum of 5 A per channel, subject to load type and thermal limits.

Choose the wiring arrangement

Use a B1 BaseUnit for two-wire connection or a B0 BaseUnit for three-wire connection.

Control fault behavior

Substitute values and supply-voltage monitoring support defined operation during faults.

Official Specifications
Output Contacts 4 isolated normally open relay contacts
Electronics Supply 24 V DC nominal; 19.2–28.8 V DC
Current Without Load Maximum 55 mA
Typical Power Loss 1.5 W
Nominal Switching Voltages 24–120 V DC or 24–230 V AC
Rated Resistive Contact Current Maximum 5 A per channel
Rated Inductive Contact Current Maximum 2 A
Minimum Switching Load 100 mA at 5 V DC
Module Total Current Maximum 20 A, subject to mounting and temperature derating
Horizontal Thermal Limits 20 A up to 50 °C; 16 A up to 60 °C
Vertical Thermal Limits 20 A up to 40 °C; 16 A up to 50 °C
Maximum Switching Frequency 2 Hz with resistive loads; 0.5 Hz with inductive loads
External Fuse Maximum 6 A, quick-response
Output Address Area 1 byte; 1 input byte for quality information
Maximum Load Cable Length 1,000 m shielded; 200 m unshielded
Operating Temperature −30 to +60 °C horizontally; −30 to +50 °C vertically
Isolation Test Voltages 2,500 V DC from channels to backplane; 707 V DC from backplane to supply
Dimensions (W × H × D) 20 × 73 × 58 mm
Net Weight 40 g
Official source:Siemens product data sheet
Frequently Asked Questions

Which BaseUnit should I choose for two-wire loads on 6ES7132-6HD01-0BB1?

Use a B1 BaseUnit for two-wire connection or a B0 BaseUnit for three-wire connection.

Does 6ES7132-6HD01-0BB1 provide built-in output short-circuit protection?

The relay outputs require external protection with a quick-response fuse rated no higher than 6 A.

Can all four channels of 6ES7132-6HD01-0BB1 carry 5 A at 60 °C in horizontal mounting?

The total module current is limited to 16 A at 60 °C with horizontal mounting.

How quickly can 6ES7132-6HD01-0BB1 switch an inductive load?

The maximum inductive switching frequency is 0.5 Hz, and DC inductive loads above 0.1 Hz require a diode.

Can 6ES7132-6HD01-0BB1 diagnose a broken load wire?

The module monitors the supply voltage but does not provide wire-break monitoring.

Is 6ES7132-6HD01-0BB1 suitable for very low-level 10 mA signals?

The specified minimum switching load is 100 mA at 5 V DC.

Can I configure substitute values for 6ES7132-6HD01-0BB1?

The module supports parameterizable substitute values for its outputs.

Compatibility & Ordering Notes
Before ordering 6ES7132-6HD01-0BB1: Choose a B0 or B1 BaseUnit and size the external protection for each connected load.

Before installation

  • Use BaseUnit type B0 or B1 with the CC40 color code.
  • Configure with TIA Portal V14 or STEP 7 V5.5 SP3 or later.
  • Select external fuses and load-suppression components for the connected circuit.
  • Apply the total-current derating for the mounting orientation and cabinet temperature.
Hot Selling Models
36-15M/S3059 U-81177
6ES5440-8MA21
516-114-GS 4-H BES0166
1SNA399706R1400
P3-63/I4-SI-SW
20084
6EP1935-6MC01
ABB 1SBH143001R8853 NL53E
S440
DA0015
MGPM25TF-25Z
1756-M08SE
M08EC-PSC15B-S49G
E24 1070075924-103
BA9053/12 0053182

Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
email goToTop

Evolo Automation is not an authorized distributor unless otherwise specified, representative, or affiliate of the manufacturer of this product. All trademarks and documents are the property of their respective owners and are provided for identification and informational.