Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
siemens 6es7132 6bh00 0ba0 simatic et 200sp dq 16x24vdc 0 5a st output module-0

For SIEMENS

Home >  Products >  For SIEMENS

Siemens 6ES7132-6BH00-0BA0 SIMATIC ET 200SP DQ 16x24VDC/0.5A ST Output Module

Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: Germany
Warranty: 12 Months

  • Overview
  • Hot Selling Models
  • Recommended Products
Overview
SIEMENS SIMATIC ET 200SP

6ES7132-6BH00-0BA0 SIMATIC ET 200SP DQ 16x24VDC/0.5A ST Output Module

Sixteen PNP outputs with 0.5 A per channel, temperature-dependent module current limits and configurable module diagnostics.

At a Glance

Brand Siemens
Model 6ES7132-6BH00-0BA0
Product Type Standard digital-output module
Core Function Driving DC field actuators
Application ET 200SP stations

Sixteen PNP channels

Positive-switching outputs drive DC contactors, valves and indicator loads.

Temperature derating

The available module current depends on ambient temperature and mounting orientation.

BaseUnit A0

The output module uses A0 BaseUnits and CC00 color identification.

Product Overview

6ES7132-6BH00-0BA0 controls sixteen 24 V DC loads in an ET 200SP station. Each PNP channel is rated at 0.5 A, with a module total of up to 8 A under the stated installation conditions.

Configurable substitute values determine the response to CPU STOP. Module-level diagnostics cover supply voltage, wire break and short circuit, and optional quality information adds two bytes to the input address space.

Ordering focus: Match the A0 BaseUnit, CC00 assignment, actuator loads, current derating and configured CPU STOP response.
Key Functions

Switch PNP loads

Sixteen positive-switching outputs provide 0.5 A per channel.

Set the STOP reaction

Channels can turn off, retain their last value or use configured substitute values.

Monitor module conditions

Configurable diagnostics and optional quality information support commissioning and fault evaluation.

Official Specifications
Digital outputs 16, PNP source outputs
Rated supply and permitted range 24 V DC; 19.2–28.8 V DC
Maximum current without load 60 mA
Typical power loss 1 W
Output current per channel 0.5 A
Horizontal module-current limits 8 A up to 40 °C; 6 A up to 50 °C; 4 A up to 60 °C
Vertical module-current limits 8 A up to 30 °C; 6 A up to 40 °C; 4 A up to 50 °C
Typical short-circuit response threshold 0.7–1.3 A
Maximum lamp load 5 W
Load resistance range 48 Ω–12 kΩ
Maximum signal-0 residual current 0.1 mA
Typical output delay with resistive load 50 µs for 0→1; 100 µs for 1→0
Maximum switching frequency Resistive 100 Hz; inductive 2 Hz; lamp 10 Hz
Address-space allocation 2 output bytes; an additional 2 input bytes for quality information
Maximum cable length 1000 m shielded; 600 m unshielded
Diagnostic scope Module-level supply-voltage, wire-break and short-circuit diagnostics
Local indicators Green PWR and channel LEDs; green/red DIAG LED
Electrical isolation Outputs separated from backplane; no separation between channels
Insulation type-test voltage 707 V DC
Width and approximate weight 15 mm; 28 g
Frequently Asked Questions

May I install 6ES7132-6BH00-0BA0 on a BaseUnit type A1?

Use BaseUnit type A0 because an A1 fuse can be triggered and render its terminals unusable.

Where must the load group for 6ES7132-6BH00-0BA0 begin?

The load group must begin with a light-colored BaseUnit.

How much total current can 6ES7132-6BH00-0BA0 carry horizontally at 60 °C?

The module-current limit is 4 A in that installation condition.

Which responses to CPU STOP can I select for 6ES7132-6BH00-0BA0?

You can select turn off, keep last value or output a configured substitute value.

Why might a small indicator flicker when an output of 6ES7132-6BH00-0BA0 is off?

The low residual current associated with wire-break detection can cause indicator diodes to flicker.

Does the quality information of 6ES7132-6BH00-0BA0 identify each faulty output independently?

A fault on one channel sets the quality status of all channels to zero.

Will parameters written to 6ES7132-6BH00-0BA0 with WRREC remain after a restart?

The STEP 7 parameter settings become effective again after restart.

Compatibility & Ordering Notes
Before ordering 6ES7132-6BH00-0BA0: Select the complete 6BH00 Standard output module with a type A0 BaseUnit, the CC00 assignment and the correct load-group, diagnostic and STOP settings.

Compatibility Checklist for 6ES7132-6BH00-0BA0

  • Use BaseUnit A0 with CC00 identification.
  • Start the load group with a light-colored BaseUnit.
  • Check each 0.5 A output and the orientation-dependent module current.
  • Configure module-level diagnostics and the desired CPU STOP response.
  • Allocate the additional input bytes if quality information is enabled.
Hot Selling Models
KFD2-SCD-Ex1.LK
KFD2-ST2-Ex2
02.110.1.006
NZM1XTVDVR
Cube67 DI8C 8xM8 56622
3RT1046-1BB44 3RH1921-1HA22 3RT1926-1BB00
103006K20M050E
5TT3 407
DSNU-25-500-PPS-A
S3-M 1847
ABB 1SFA616070R2031 KL70-203R
JMVH-5-1/4-B
3RT1046-1BB44 E:05 + 3RH1921-1HA22 E:06 + 3RT1926-1BB00
Detas 900316
3VA9603-0QA00

Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
email goToTop

Evolo Automation is not an authorized distributor unless otherwise specified, representative, or affiliate of the manufacturer of this product. All trademarks and documents are the property of their respective owners and are provided for identification and informational.