Siemens 6ES7132-4BD01-0AA0 SIMATIC ET 200S 4DO DC24V/0.5A ST Output Module

Overview

SIEMENS SIMATIC ET 200S

6ES7132-4BD01-0AA0 SIMATIC ET 200S 4DO DC24V/0.5A ST Output Module

A standard four-output ET 200S module with 24 V DC load supply, 0.5 A rated output current and individual green status LEDs.

At a Glance

Brand	Siemens
Model	6ES7132-4BD01-0AA0
Product Type	Digital output module
Core Function	Four-channel actuator control
Application	ET 200S distributed I/O stations

Standard DC outputs

The four channels switch solenoid valves, DC contactors or indicator lights.

Load-specific timing

The specified switching rate differs for resistive, inductive and lamp loads.

Packed output allocation

Four output bits can be packed within the ET 200S process-image arrangement.

Product Overview

6ES7132-4BD01-0AA0 controls four 24 V DC actuator circuits within an ET 200S potential group.

The standard module supports isochronous operation and short-circuit-protected outputs, with output delays and no-load current specified for this exact 4BD01 revision.

Ordering focus: Select the 4BD01 revision with its own output timing and current limits, a compatible TM-E terminal base and the correctly supplied 24 V DC group.

Key Functions

Switch four distributed field loads

Each output carries a rated 0.5 A and the module total is limited to 2 A.

Accommodate the actuator switching duty

Resistive loads can switch at 100 Hz, inductive loads at 2 Hz and lamps at 10 Hz.

Display channel state at the station

A green LED per output indicates its activation while the standard module provides no diagnostic function.

Official Specifications

Rated load supply	24 V DC from the power module
Rated output current	0.5 A per channel; signal-1 range 7–600 mA
Total module output current	2 A
Maximum no-load current from L+	5 mA per channel
Maximum signal-0 leakage current	0.3 mA
Typical module power dissipation	0.8 W
Minimum signal-1 output voltage	L+ minus 1 V
Maximum resistive-load output delays	100 µs turn-on; 300 µs turn-off
Load resistance range	48 Ω–3.4 kΩ
Maximum lamp load	5 W
Load-dependent switching rates	100 Hz resistive; 2 Hz inductive; 10 Hz lamps
Maximum unshielded and shielded cable lengths	600 m and 1000 m respectively
Output process-image allocation	1 byte normally; 4 bits when packed
Parameter length	1 byte
Isolation arrangement	No isolation between channels; channels isolated from backplane bus
Permissible inter-circuit potential difference	75 V DC or 60 V AC
Insulation test voltage	500 V DC
Status indication	One green LED per output
Module width	15 mm
Approximate module weight	40 g

Official source:Siemens exact 4BD01 module manual

Frequently Asked Questions

What turn-on and turn-off delays should I allow for with 6ES7132-4BD01-0AA0?

With resistive loads the maximum output delays are 100 µs for turn-on and 300 µs for turn-off.

How much current can 6ES7132-4BD01-0AA0 draw from L+ before actuator load current is added?

Its no-load current consumption is at most 5 mA per channel.

Can 6ES7132-4BD01-0AA0 switch a resistive load at 500 Hz?

No, the specified resistive-load switching rate is 100 Hz.

What leakage current can remain at an inactive output of 6ES7132-4BD01-0AA0?

The maximum signal-0 leakage current is 0.3 mA.

May I parallel outputs on 6ES7132-4BD01-0AA0 for redundant triggering?

Yes, parallel connection is permitted for redundant triggering within the module, but not to increase output capacity.

Does 6ES7132-4BD01-0AA0 require all four channels to be individually isolated?

No, its channels are not isolated from one another, although they are isolated from the backplane bus.

Can 6ES7132-4BD01-0AA0 switch a lamp load larger than 5 W?

No, the specified maximum lamp load is 5 W.

Compatibility & Ordering Notes

Before ordering 6ES7132-4BD01-0AA0: Match the 4BD01 output timing and leakage limits, keep the module’s aggregate load within 2 A and choose the TM-E base that fits the actual actuator wiring.

Compatibility Checklist for 6ES7132-4BD01-0AA0

• Use a compatible 15 mm TM-E terminal module.
• Apply 24 V DC from the correctly selected power module.
• Respect the 100/2/10 Hz load-specific switching rates.
• Do not parallel channels to increase current capacity.

Hot Selling Models