Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
siemens 6es7131 4bb01 0ab0 2 di hf 24 v dc pack of 5-0

For SIEMENS

Home >  Products >  For SIEMENS

Siemens SIMATIC ET 200S 6ES7131-4BB01-0AB0 2 DI HF 24 V DC, Pack of 5

Manufacturer: Siemens
Condition: Brand New
Lead Time: In Stock
Origin: China
Warranty: 12 Months

  • Overview
  • Product Overview
  • Key Functions
  • Official Specifications
  • Frequently Asked Questions
  • Compatibility & Ordering Notes
  • Hot Selling Models
  • Recommended Products
Overview
SIMATIC ET 200S · HIGH-FEATURE DIGITAL INPUT

6ES7131-4BB01-0AB0 2DI DC24V HF Electronic Module

Siemens ET 200S electronic module with two 24 V DC inputs, configurable input delays, sensor-supply short-circuit diagnostics and isochronous operation.

At a Glance

Manufacturer Siemens
Article Number 6ES7131-4BB01-0AB0
Product Type 2DI DC24V High Feature digital electronic module
Core Function Acquires switch and proximity-sensor signals with configurable input filtering
Application / Compatible Series SIMATIC ET 200S distributed I/O
Input RoleTwo channels acquire 24 V DC discrete signals for ET 200S control tasks.
Supported SensorsSuitable for switches and two-wire proximity switches (BEROs).
Configurable ResponseInput delays of 0.1 ms, 0.5 ms, 3 ms or 15 ms are available.
Product Overview

6ES7131-4BB01-0AB0 is officially identified by Siemens as 2 DI High Feature Digital Input Electronic Module in the SIMATIC ET 200S product range.

Siemens identifies this packing unit of five ET 200S High Feature electronic modules with two 24 V DC digital inputs per module, parameterizable input delay, sensor short-circuit diagnostics and an SF group-fault LED.

Ordering focus: verify the complete 6ES7131-4BB01-0AB0 article number, installed hardware configuration, connections and Siemens system documentation before replacement.

Key Functions

Model-Specific Configuration

6ES7131-4BB01-0AB0: Five 15 mm ET 200S electronic modules, each with two High Feature 24 V DC digital inputs.

System Connection

ET 200S terminal-module and backplane connection with input-delay parameterization and diagnostics.

Replacement Control

Use the full 6ES7131-4BB01-0AB0 article number and official Siemens documentation to verify the installed configuration before replacement.

Official Specifications
Number of Digital Inputs 2
Nominal Input Voltage 24 V DC
Signal 1 Voltage Range 11–30 V DC
Signal 0 Voltage Range -30–5 V DC
Input Current at Signal 1 Typically 8 mA
Configurable Input Delays 0.1 ms, 0.5 ms, 3 ms or 15 ms
Input Characteristic IEC 61131 Type 1
Two-Wire Proximity Sensors Supported
Maximum BERO Bias Current 1.5 mA
Sensor Supply Output Voltage Minimum L+ minus 0.5 V
Sensor Supply Output Current 0–500 mA; rated 500 mA
Sensor Supply Protection Electronic short-circuit protection
Isochronous Operation Supported
Address Space 1 byte; 2 bits when packed
Parameter Length 3 bytes
Shielded Cable Length Up to 1,000 m
Unshielded Cable Length Up to 600 m
Electrical Isolation Channels share potential; isolation is provided to the backplane bus
Insulation Test Voltage 500 V DC
Power Dissipation Typically 0.4 W

Official source: Siemens ET 200S 2DI DC24V HF product manual A5E01077133-01.

Frequently Asked Questions

Which sensors can be connected to 6ES7131-4BB01-0AB0?

The inputs accept mechanical switches and 24 V DC proximity switches, including two-wire BEROs within the permitted bias-current limit.

How should an engineer select the input delay for 6ES7131-4BB01-0AB0?

Choose 0.1 ms, 0.5 ms, 3 ms or 15 ms according to the required response time and the amount of input-signal filtering needed.

What short-circuit diagnostic does 6ES7131-4BB01-0AB0 provide?

A short circuit on the sensor supply is reported on channel 0 and applies to the complete module; the SF LED indicates the group fault.

Can 6ES7131-4BB01-0AB0 be used in an isochronous ET 200S application?

Yes. Isochronous operation is supported.

Which field-wiring arrangements are supported by 6ES7131-4BB01-0AB0?

The approved 15 mm terminal modules support two-wire, three-wire and four-wire sensor connections; four-wire wiring uses AUX1 connected to PE through the PM-E.

Are the two input channels of 6ES7131-4BB01-0AB0 electrically isolated from each other?

No. The channels share the same potential, while the input circuits are isolated from the ET 200S backplane bus.

Which interface modules allow process-interrupt parameterization for 6ES7131-4BB01-0AB0?

Rising-edge process interrupts can be parameterized with an IM151-1 HIGH FEATURE interface module or an IM151-7 CPU.

Compatibility & Ordering Notes
Before ordering 6ES7131-4BB01-0AB0: compare the complete article number, official configuration, system connections and required Siemens accessories with the installed unit and documentation.

Compatibility Checklist for 6ES7131-4BB01-0AB0

  • Match the complete 6ES7131-4BB01-0AB0 article number without shortening the suffix.
  • Confirm compatibility with the installed SIMATIC ET 200S product range.
  • Verify Five 15 mm ET 200S electronic modules, each with two High Feature 24 V DC digital inputs.
  • Confirm ET 200S terminal-module and backplane connection with input-delay parameterization and diagnostics.
Hot Selling Models
XC-1500-580-WT-RD
HCPS.9-2508W
LC-103X15-B7644
HLF399S 323093
VBA-1E1A-G10-ZAL/E2L-1M-2V3-G
KMEB-2-24-M12-0,5-LED
MX153
TB40-100-00000-D35
047H0213 TI 25C
514.001.113 MCP250M
WP-700-EB
RS-481
FHS-025
7070-03149-01
BL0117

Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
email goToTop

Evolo Automation is not an authorized distributor unless otherwise specified, representative, or affiliate of the manufacturer of this product. All trademarks and documents are the property of their respective owners and are provided for identification and informational.