Siemens 6ES7193-4JA00-0AA0 SIMATIC ET 200S Bus Terminating Module

Conspectus

Siemens SIMATIC ET 200S

6ES7193-4JA00-0AA0 SIMATIC ET 200S Bus Terminating Module

The replacement terminating module for the end of an ET 200S assembly, mechanically joined to the final terminal module to complete the station.

Ad Primum Aspectum

Nota	Siemens
Modellum	6ES7193-4JA00-0AA0
Typus Producti	Station bus terminating module
Functio principalis	Completing the station backplane bus
Applicatio	Right-hand end of an ET 200S station

Required station ending

The ET 200S is not ready for operation without its terminating module.

Last position

The terminating module follows the last terminal module at the end of the station.

Latched assembly

It pivots onto the DIN rail and locks into the terminal module to its left.

Product Overview

6ES7193-4JA00-0AA0 completes the ET 200S backplane-bus assembly at the end of the station, immediately after the final terminal module.

It is a dedicated station component rather than an electronic I/O module, and its removal or interruption of the backplane during operation requires a complete station power cycle after restoration.

Focus ordinandi: Select the ET 200S terminating module for the final station position and distinguish it from terminal-base covers or PROFIBUS cable-termination accessories.

Key Functions

Complete the ET 200S station assembly

The terminating module closes the distributed I/O assembly, which is not ready for operation if the module is absent.

Latch to the final terminal module

The module hooks onto the rail, pivots backward and slides left until it locks into the installed final terminal module.

Support planned station maintenance

Post removal et refixation sub volt, aut post restitutum interruptum dorsale, commuta totam alimentationem ET 200S ex et in ut statum stationis definitum constituas.

Official Specifications

Dimensiuni (lățime × înălțime × adâncime)	30 × 106 × 7.5 mm
Pondus Approximatum	50 g
Adfixio Mechanica	Fixatio ad DIN-rail cum coniunctione clausurae ad modulum terminalis finalis
Gradus protectionis in conformatione ET 200S	IP20 secundum IEC 60529
Temperatura ambientalis operativa ET 200S	0 ad +60 °C cum installatione horizontali; 0 ad +40 °C in aliis positionibus montandi
Humiditas relativa operativa ET 200S	15 ad 95 %, sine condensatione
Pressio aëris operativa ET 200S	795 ad 1080 hPa; altitudo −1000 ad 2000 m
Temperatura transportis et conservationis	−40 ad +70 °C in confectione originali

Fons officialis: Folium Datormum Moduli Terminantis Siemens · Instructiones operationis Siemens ET 200S

Quaestiones Frequenter Rogatae

Potestne mea statio ET 200S incipere sine modulo 6ES7193-4JA00-0AA0 installato?

Stat io ET 200S non est parata ad operationem sine modulo terminante.

Quid iam praesto esse debet antequam modulo 6ES7193-4JA00-0AA0 insereo?

Modulus terminalis finalis stationis iam installatus esse debet.

Quomodo modulo 6ES7193-4JA00-0AA0 in confectione completa constringo?

Imponatur in railem, vertatur retrorsum, deinde trahatur ad sinistram donec audibiliter in modulo terminali ultimo constringatur.

Quomodo modulo 6ES7193-4JA00-0AA0 solvo dum stationem servio?

Prematur cursor moduli terminalis ultimi deorsum usque ad finem cum cuneo, deinde modulus terminalis movetur ad dextram et a rai le vertitur.

What must I do after 6ES7193-4JA00-0AA0 has been removed and refitted under voltage?

Switch the complete ET 200S power supply off and on again to establish a defined station state.

Will 6ES7193-4JA00-0AA0 add another set of field I/O channels?

The module completes the ET 200S station bus rather than providing field input or output channels.

Should 6ES7193-4JA00-0AA0 remain at its old position after I extend the station?

The terminating module belongs after the final terminal module of the completed assembly.

Compatibility & Ordering Notes

Before ordering 6ES7193-4JA00-0AA0: Use the ET 200S bus terminating module at the final station position and plan any extension or replacement with the complete-station restart requirement.

Compatibility Checklist for 6ES7193-4JA00-0AA0

• Use this component for an ET 200S station bus assembly.
• Installez tous les modules terminaux requis avant de monter le module de terminaison.
• Verrouillez le module de terminaison sur le dernier module terminal sur le rail.
• Gardez les couvercles protecteurs des bases de bornes et les résistances de terminaison externes pour câbles bus séparés de ce composant.
• Après une interruption du bus arrière pendant le fonctionnement ou après un retrait et une remise en place sous tension, redémarrez entièrement la station.

Hot Selling Models